ENGINE CONTROLS

Product Details:

Doosan Governor Speed controller DGC-2007 Speed Governor
PID speed control
Independent or parallel operation
5 display LEDs (Power/Pickup/Run Speed/Idle Speed/Over Speed)
3 relay output channels(Over Speed/Crank Speed/Run Speed)
Droop operation
Speed control by connecting to an external resitor (ADJ)
Speed control with inputting external voltage (AUX)
Automatic stop with overspeed setting
Environment of Use
Temp. negative 20 to 80°C
Humid. 0 to 98%
Input Voltage (E-F) DC 12 to 32 V
PickUp(C-D) AC 3 V or more
Droop control(K-L) Open/ Short
Speed control(G-J) Resistance value (Refer to Control)
Speed control(G-N) DC negative 3 to 3 V
Output
Actuator control(A-B) 120W ( DC24V/5A , DC12V/10A)
Relay Output(1 to 9) AC250V/10A, DC100V/5A
LED Display Power/PickUp/Crank/Run/OverSpeed Control
Single Turn Volume Gain/Stability/Droop/Idle/Speed Ramping/Starting Fuel
Multi Turn Volume Speed/Crank LED/ Run LED/ Over Speed & LED
External Resistor Speed Control 1k/ 900Hz, 5k/2400Hz, 10k/3000Hz, 25k/3500Hz, 50k/3700Hz
External Voltage Speed Control A variance of 2,000 RPM per 1 V (number of teeth in the gear: 160)
Certification
CE Certificate DGC-2007,GNSC-2009

Product Details:

Product description:

We deal in good oem quality cummins stop solenoid 0306-5450.Please send in your inquiry for the same.

Product Details:

Product Details:

Specifications

Product Details:

Product Description

The BASLER ELECTRIC AVC 63-7 can providea DC output of 7 Adc at 63 Vdc and can sense 170 to 264 Vac. This avr can work with paralleling synchronizing generators (must specify prior to ordering).

DESCRIPTION: Basler Electric AVC 63-7, brand new , Original

PART NUMBERS: 9302800103

MANUFACTURER: Basler Electric

AVAILABILITY: In stock, same day shipping worldwide

ORIGIN: Manufactured in Highland, Illinois, USA

Product Details:

Product Description

EXPORT ONLY 

  

True RMS Sensing ± One or Three Phase: 
Connect the sensing mode you prefer. Senses 95 to 600 volts ±10% at 50/60 hertz. Patented circuitry senses true RMS voltage rather than average for superior load regulation. 

Soft-Start Ramp on Initial Start-Up: 
Controlled increase to rated voltage. Limits overshoot of voltage during voltage build-up. 

Engine Unloading: 
Monitors the rate of frequency change during transient conditions. Provides additional voltage dip during speed drop to allow engine to recover faster. 

Over voltage Shutdown: 
Provides generator protection during sustained overvoltage. The overvoltage point is preset at 20% over normal generator operating voltage, with a preset timeout of 0.75 seconds. 

VAR/PF Controller: 
Model DVR 2000EC (optional) provides control when paralleled to utility power. VAR or PF control can be selected or changed by regulator adjustment. 

Encapsulated Design: 
Maximum protection against moisture or abrasive contamination, which can lead to early regulator failure. 
Tested to MIL-STD-705, Method 711.1C. Salt fog tested 
to MIL-STD-810E. 
Auto/Manual Mode: 
Exciter field current can be controlled by the regulator or manually set at a fixed value

Product Details:

Genuine Parts Offerings

We deal in following products which cater to over 17 engine series, 30 basic engine models with 400 different applications and over 25,000 line items.

• Genuine Cummins Parts
• Engine Overhaul and Repair Kits
• B Check Kits
• Conversion and Engine Upgrade Kits
• Cummins Filtration Products
• Genuine Cummins Parts for Tata Cummins engines
• Cummins Turbocharger Assemblies and Parts
• Silencers and Emission products
• Genset Alternators and Spares
• Filtration and Coolants
• Special repair / Diagnostic tools
• Electrical / Electronic / Software Items
• Accessories / Peripherals
• Training Aids / Literature / Cut Models

 

Why Buy Genuine Parts?

It Makes Genuine Difference
Appearances can be deceptive! This is especially true when it comes to critical parts for your engine. Pistons, for example; a Cummins genuine pistons and a local made piston may look exactly same; however on closer inspection we can find a drastic differences between the two. There could be differences in design, tolerances and materials. The truth is, Genuine Cummins Parts deliver improved performance and longer life between overhauls. It's that simple.

Genuine Cummins Parts

• Meet exacting Cummins specifications
• Utilize advanced materials
• Incorporate state-of-the-art Cummins design technology
• Are continually improved
• Have an industry-leading warranty
• Are backed by a Best in Class nationwide Service Network

Every Part Proven

Cummins parts undergo countless hours in the test cell, plus millions of hours in field testing, to ensure reliability and durability. Genuine Cummins Parts are proven and dependable. Others aren't.

Even though a non-genuine part might apparently fit your Cummins engine, there is no guarantee it will perform. Others try to copy Cummins components without knowing the technology, design and materials specifications that are critical to performance. Installing non-genuine parts may cause early failure which can result in unscheduled downtime and increased repair costs. Play it safe and smart - purchase your replacement parts from an authorized Cummins distributor or dealer.

Parts Support

We always ensure:

• Availability at the point of consumption.
  • Robust Parts Supply Chain to ensure all fast moving parts are available and maintained closer to customer locations.
  • Periodic review to suit the demand changes.
• Easy to Operate ‘Parts Rate Contracts.
• Priority shipping of Break Down Engine Parts.
• Shipping in Customer convenient lots.
• One stop shop for Cummins Generator requirements.
• Solutions through
  • Maintenance Kits.
  • Engine Repair / Overhaul Kits.
  • Conversion and Upgrade Kits.
  • Filtration, Exhaust and Emission solutions.
  • Reduction in TCO thru’ value added products like HRU, Coil Coolers.

Product Details:

Product description:

GCU is a 1-phase / 3-phase Automatic / Manual Generator controller module including protection for (STANDBY) GEN-SETS. It uses an advanced single chip microcomputer for an easy and trouble free GEN-SET control in case of mains power failures. If mains fail (over / under voltage, loss of mains voltage), GCU initiates an automatic GEN-SET start cycle including load transfer to the generator by switching the generator contactors. After the mains is restored the load will be automatically transferred back to mains and the GEN-SET will stop after a cool down time. During all cycles, generator is fully protected against malfunction. All alarms occurring at abnormal GEN-SET conditions are computed and displayed either by LED or by the four-digit display and if necessary the GEN-SET gets stopped.
Values of over/under voltage, frequency and overload current (see parameter No.: 6,7,9,10,11) and timer settings for Preheat, cooling down time (see parameter No.: 5,14) etc. are programmable. The GCU has 40 powerful programmable parameters to fit the program flow to customer needs.

 

Product Details:

Product DescriptionThere is no comfort like being in command. KOEL Green Generators put the command in your hands. Micro-processor based Generator controllers display a host of Generator parameters and put all controls at your fingertips.

 
KG controllers have the following features:
 

• Genset monitoring: KG controllers monitor vital genset parameters and provide necessary protection to ensure that the KOEL green genset operates reliably
• Genset metering: KG controllers have built in metering of key electrical and engine parameters
• AMF compatibility: All KG controllers are compatible with AMF panels
• Communication capability: All KG controllers have an in built communication port to connect to your BMS/SCADA system

Product Details:

Product description:

GCU is a 1-phase / 3-phase Automatic / Manual Generator controller module including protection for (STANDBY) GEN-SETS. It uses an advanced single chip microcomputer for an easy and trouble free GEN-SET control in case of mains power failures. If mains fail (over / under voltage, loss of mains voltage), GCU initiates an automatic GEN-SET start cycle including load transfer to the generator by switching the generator contactors. After the mains is restored the load will be automatically transferred back to mains and the GEN-SET will stop after a cool down time. During all cycles, generator is fully protected against malfunction. All alarms occurring at abnormal GEN-SET conditions are computed and displayed either by LED or by the four-digit display and if necessary the GEN-SET gets stopped.
Values of over/under voltage, frequency and overload current (see parameter No.: 6,7,9,10,11) and timer settings for Preheat, cooling down time (see parameter No.: 5,14) etc. are programmable. The GCU has 40 powerful programmable parameters to fit the program flow to customer needs.

 

Product Details:

Wea dealing engine controls saftys sensor / governor controllers actuator all engine parts etc . . .

Product Details:

Product Description

We take a huge pleasure in the market by offering best and elite quality array of Engine Controller. These offered controllers are best and designed by our most qualified professionals. They are used to control the engines of pumps, compressors, crane, etc. They are designed with the assistance of modern machines and tools to keep it as per required standards. They are accurate and easy to install. Our customers can get cost effective rates.

 

Features:

• Highly efficient

• Robust structure

• Modern design

 

Product Details:

Product Details:

Quick Details Place of Origin:Chongqing, China (Mainland)Brand Name:Delcot Model Number:C2002Model nunber:C2002Product name:Speed Controller C2002Material:iron- boxRPM Stability:<±0.25%Test temperature:75 degree Reliability Testing:100% Functionally Purpose:brushless generator Weight:0.658Reliability vibration:1G at 20 to 100 Hz Working humidity range:maximum 95%

Product Details:

SPECIFICATION:

 

Synchronization function for diesel brushless generator Speed Controller SYC6714

 

SYC6714 synchronous generator Product description:

It is a subsidiary of the device with a parallel between the engine, which can adjust the parameters to the unit's AC AC parameters are consistent with the external bus, so that the current generator can be successfully incorporated into the bus to go working principle: it contains portions of the phase angle difference, the synchronization detection section window range, stable control of the engine speed and the gain adjustment section. When the detected current phase angle difference between the generator and the bus within a preset range of the output of a synchronous window relay signals to external devices and machines, if the phase angle difference is not within the range it will output an analog signal to the governor , a rapid change in engine speed, so that the phase angle difference is within the range, the synchronization process is completed. Under normal circumstances a good speed performance, and the car in less than3 seconds.

 

Note: Theoretically there is no limit with generator range, and a lot can usually be and two more ranges (limit up to 99 generating units).

Product Details:

Specifications

1)Introduction:

The S6700E Speed control Unit is an All-Electronic Device Designed to control engine speed with fast and precise response to transient load changes. Based on a closed loop control. The basic characteristics of this unit is to reach rated speed and power as well as reducing smoke exhaust through adjustment of firing fuel and speed-rate. The S6700E speed control Unit provides a series of protection once the power supply is reversely connected. Transient overvoltage or actuator fault happens, or Speed input breaks.

• Power reverse connection protection
• Actuator default protection   
• Speed signal Lose protection
• Over-speed & External high Level input Alam

Environmental

Ambient operating temperature range   - 40 ~ 85 °C

Relative humidity   95%

Input Power

Supply           24VDC

Actuator current range   2.5-10A(continuous)

Speed sensor signal   1-20v

Characteristics    

Speed fine adjustment range   ± 100% r / min

Frequency fluctuation          ± 0.25% 

Steady speed droop           0~3% (variable)

Temperature drift               ± 1% (maximum

Product Details:

Specifications

• Sensing Input
• Voltage 170 to 510 Vac 1 phase 2 wire DIP switch selectable
  Frequency 50/60 Hz

• Power Input
• Voltage 60 to 300 Vac 1 phase 2 wire

• Excitation Output
• Voltage 240V 1 phase
  Current Continuous 63 Vdc 16A Max. 90 Vdc 20A for 10 seconds
  Resistance Min. 5 ohms

• Volts Regulation
• Less than +/-0.5% (with 4% engine governing)

• Build Up Voltage
• Residual volts at AVR terminal greater than 5 Vac

• Thermal Drift
• 0.03% per °C change in AVR ambient

• Over Excitation Protection
• Max. DCV 95% 20 seconds

• External Volts Adjustment
• +/-5% with 2 KΩ 1 watt trimmer

• Unit Power Dissipation
• Max. 10 watts

• Under Frequency Protection
• 55 Hz @ 60 Hz (adjustable)
  45 Hz @ 50 Hz (adjustable)

• Analogue Input
• Max. +/-5 Vdc +/-10% @ +/-3 Vdc

• CT Current Compensation Input
• 1A or 5A (adjustable)

• Operating Temperature
• -40 to +70 °C

• Storage Temperature
• -40 to +85 °C

• Relative Humidity
• Max. 95%

• Vibration
• 3.3 Gs @ 100 to 2K Hz

• Dimension
• 162.0 (L) x 112.0 (W) x 43.0 (H) mm

• Weight
• 535 g +/-2%

AVR Control Functions

• VOLT
• Voltage adjustment

• STAB
• Stability adjustment

• U/F
• Setting under frequency protection knee point

• DROOP
• Current compensation droop adjustment

• TRIM
• Analogue input adjust

Product Details:

Brief Introduction:

* EFC3037359 is a engine speed controller designed by all electronic device for 's actuator.

* It can fast and precise response to transient load changes.

* It has a wide speed control range.  

* For these controllers, separate circuits allow adjustments of proportional, integral and derivative values.

*These parameters all work together to provide a control that results in fast and stable engine response to load changes

Parameter   
EFC 3037359

Product Details:

Brief Introduction:

Application Features 
A. Low smoke displacement, soft noise Meet the demand of environment protection imp rive people' S Feeling. 

B. Easily start in cold, plateau and Ww pressure areas, Especially for N-G-250kw and K-G-300kw sets. 

C. High ability to anti-disturbance Stable operation due to the large power walkie-talkie· 

D. Actuator can not be damaged in case of short circuit due to The output protector. 

E. Diesel with water pump cam start with wad, the range of round per minute cam be ± 600, that is 1000-1200 rpm. Principles The oil valve of the speed regulator is totally Open and if the supercharger low-speed and with little Air input, So it is difficult to ignite the fuel and cannot Completely ignite and have thick smoke displacement. It starry400-1200rpm, It need 3-5or 10-20 minute To accelerate. 

It can easily start if we decrease the oil input. After it start, then increase' The oil input, the speed and the diesel generator temperature will increase gradually. Thus, the smoke displacement is Ww and the noise is soft. 

The operation of and use of the set after start is same as other regulators. 

Operation methods

A. Apearance Feature: It is same as other regulators. 
B. Switchesc: Seitches for after start while all the 3 switches downside, it can ccelerate immediately, while switch them upside respectively. It can accelerate in 5' , 10' , 15respectively. 
As the picture described (7-10 cannot connect prompt switches). The time more needs the smoke thinner and much easier to start. 
C. The lasting time of the start switch vibration is a little wag... 
During acceleration, if there is displacement stroke and displace black smoke, please regulate GAIN. 
D. If the sets adopt self-start 

Product Details:

Product Description

Electronic fuel control(efc)
Specification:
Rpm stability: <± 0.25%
Speed range: 1KHz ~ 6.5KHz
Thermal stability: Max ± 0.7%
Idle regulation: 260 ± 20Hz
Droop regulation: Minimum 15Hz ± 6Hz/ 1 amp
Maximum: 400Hz ± 75Hz/ 1 amp
External speed regulation: ± 200Hz (with 1 kω Connected)
Aux input sensitivity: 148Hz / 1v., ± 10Hz
Impedance: 1mω
Working temp range: -40 ~ 85
Environment:
Working humidity range: Maximum 95%
Stocking temp: -55 ~ 92
Shocking: 20-100Hz 500mm/sec.
Input power supply
Voltage: 24v
Grounding pole: Negative pole
Power supply: 40ma
Actuator continuous current: Minimum 1a, maximum 4.5a
Mpu
Signal: 2 ~ 120v RMS
Note: Above-mentioned parameters are tested with a 3800Hz working frequency.

control panel model:
3044195
3044196
3062322
3032733
3037359
actuator model
3408324
3408326
3408328
We are selling the above model control panel for genuine & replacement parts.

Product Details:

Silent Power Generator & DG Set Repair and Service 

TMTL Engines Division is a unit of TAFE Motors and Tractors Limited (TMTL) with Alwar, Rajasthan, India, as its manufacturing base. TMTL is a wholly owned subsidiary of Tractors and Farm Equipment Limited (TAFE), part of Chennai based Amalgamations Group, which is one of India''s largest light engineering conglomerates. The Amalgamations Group has a long and distinguished history of serving Indian and global markets with a pan India presence of over 41 companies and is renowned for its highest standards of integrity, ethics and values, backed by a highly skilled and competent workforce of over 15,000.

The TMTL Engines'' Alwar plant at Rajasthan, India, produces a wide range of air and water cooled engines in the brand names of EICHER ENGINES (upto 45 kVA) and TMTL ENGINES (62.5 kVA & above), which cater to a wide range of automotive and stationary applications and has an existing customer base of over 1 million spread across various segments.

Engines manufactured by TMTL are one of the most preferred engines for stationary applications like generators, prime mover for agro-industries and other industrial applications.

In power generation segment, TMTL has a strong base of loyal customers and stands as one of the market leaders through continuous improvements in product features and product range, by using advanced technology and exceptional customer service that meet the global standards of quality and productivity.

TMTL envisages growing exponentially in the power generation segment by providing economical power solutions with custom built products and services catering to a wide range of institutional and retail customers ranging from banking and finance, commercial, construction and real estate, hospitality, information technology, government and public sector, small and medium enterprises, petrol pumps, educational institutes and hospitals.

Product Details:

LSM672N Speed Controller

Generator parts Load Share Model LSM672N.load distributor.Parallel generator function

Description----The function of the Load Sharing Module is to proportionally share load between two or more generator sets while the system frequency is held constant.As an accessory to the electronic Governing System,the LSM672N measures the true power current ,and throught a parallel cable interconnection,continuously controls the governor system. 
Performance: 
Load Sharing……Adjustable to within +/-2% between sets 
Performance…….Isochronous and droop paralleling and power control 
Reverse Power Monitor….Adjustable from 0.5-20% with a 2 second inverse time constant                                  
Forward Power Monitor……“ON”trip point adjustable from 20-100%                        
                                            “OFF”trip point adjustable from 0-80%                   
                                               Normally open contacts with a 2 second inverse time constant 
Power Output Signal…….0 to 7.5 Volts DC representing 0-100% load 
All performance specifications are based on 5 amps from the current transformer(CT) Secondaries at full load unity P.F. 
Power input : 
AC input signals….. 208 or 416 volt nominal line to line and 5 amp CTs with a minimum 6.25 VA rating.                   

Internal 0.25 ohm burden resistors 
Line to line voltages………per table below             
HZ      LOW RANGE          HIGH RANGE            
50      140-250 VAC         260-420 VAC             
60      170-260 VAC         340-500 VAC            
400    170-260 VAC         340-500 VAC 
DC Supply………..18-36 VDC(Transient and reverse voltage protected)
DC Power Consumption……….70 ma continuous

Product Details:

Product DescriptionGenerator Electronic Governor Controller also known as Engine Speed Control or Engine Governor. It has smoke limit and idle speed control. It's suitable for petrol generator, diseal generator, and natural gas generator. It's compatible with ,Woodward,Barber Colman, and GAC's governor.Product Feature

• DIP switch settings allow a wide range of MPU/flywheel frequencies
• 15 Amp max. current output to drive actuator
• Suitable for all types of diesel, gas and petrol engines
• High sensitivity and stability at low frequency variations
• Isochronous mode for individual (island) operation
• Droop mode for parallel operation with PLC control (non-isochronous)
• Connections for remote speed potentiometer
• Input for Isochronous Load Sharing (ILS) from an external load controller

Product Specification / Models

Product Details:

Specifications:
Operating Voltage: DC 10V~30V
Output Current: 0.5A~15A
Frequency Range: 600-9500 Hz (MPU signal)
Idle Speed Frequency: Adjustable from 30-85% of normal
Speed Band: +/- 0.25% at steady state
Temp. Stability: Between -40~+85 °C better than +/- 0.5%
Remote Speed Adjustment Range (2 mode): Adjustable range +/- 5% with 5KΩ potentiometer
Ramp Time: 3~20 sec. (Adjustable)
Operation Environment:
Operation Temperature : -40~+85 °C
Storage Temperature : -40~+85 °C
Relative Humidity : Max. 95%
Vibration : 3Gs @ 100-2K Hz
DIP Switch Description:
SW1 : ON 600-1200 Hz
SW2 : ON 1200-2500 Hz
SW3 : ON 2500-5000 Hz
SW4 : ON 5000-9500 Hz
Governor Controls:
DROOP : Droop Rate Adjustment
GAIN : ACT Output Gain Adjustment
INT. : Engine Stability Adjustment
RAMP-TIME : Soft Start Adjustment
SPEED : Speed Adjustment
IDLE : Idle Speed Adjustment
Dimension: 147 x 114 x 40mm
Weight: 690g

Product Details:

WE ARE DEALING  PT SPEED CONTROLLER AND PT ACTUATOR / SENSOR/ SWITCHES AND ALL PANELS ETC 

Product Details:

WE ARE DEALING SPEED CONTROLLERS AND SENSOR ,SWITCHES , ENGINE SPARE PARTS ETC...

Product Details:

WE DEALING FOR ALL TYPE OF CONTROLS AND SENSOR WITH ENGINE SPARE PARTS 

Product Details:

We are dealing control and modules and also  engine pares.

Product Details:

we are dealing speed governor controlls with engine spare parts and - etc

Product Details:

Cummins speed governor 4913988,Cummins speed governor,speed governor 4913988,Good quality and competitive price
Cummins speed governor 4913988,Cummins speed governor,speed governor 4913988,
controller board 4913988 cummins engine M11 NT855 K19 K38 K50
controller board 4913988 cummins engine M11 NT855 K19 K38 K50
controller board 4913988 For the following Cummins Engine
M11 M11
M11 M11-280-330ESP1
M11 M11-280E
M11 M11-280E PLUS
M11 M11-305E PLUS
M11 M11-310
M11 M11-310-370ESP2
M11 M11-310E
M11 M11-310E PLUS
M11 M11-330
M11 M11-330-370ESP
M11 M11-330-370ESP +
M11 M11-330E
M11 M11-330E PLUS
M11 M11-330E-FIRETRK
M11 M11-335E
M11 M11-335E PLUS
M11 M11-340E PLUS
M11 M11-350
M11 M11-350-400ES
M11 M11-350-400ESP
M11 M11-350-400ESP +
M11 M11-350E
M11 M11-350E PLUS
M11 M11-370 ESP PLUS

Product Details:

Description:

1.generator parts
2.PCB 650-091,12V
3.PCB 650-092,24V
4.EIM 630-465,
5.Weight:0.41KG

PCB 650-091,12V
PCB 650-092,24V
EIM 630-465,
EIM630-466.

PCB 650-091,12V
PCB 650-092,24V

The 650-091 Printed Circuit Board for gensets OLYMPLAN-MASSEY FERGUSON 12V.

The 650-092 Printed Circuit Board for gensets OLYMPLAN-MASSEY FERGUSON 24V.

We can supply the following products:

PCB 650-091,

PCB 650-092.

EIM 630-465,

EIM630-466.

More Picture And Package

FEATURES

• PC configurable;• Digital and analogue inputs• Digital output

• Automatic mains (utility) supply monitoring

• Automatic shutdown or warning when fault conditions are detected

• Front panel programming

• Tamper proof engine hours counter

• Remote start

Product Details:

WE ARE DEALING ,

BE1  BE16 BE20 BE21  BE22  BE23  BE24  BE28  BE32 
BM80   BEK3   BE42  BE46  BE124  BE142  BE2K  BE2000  
BE2KP  BE126

Product Details:

The 650-091 Printed Circuit Board for gensets OLYMPIAN-MASSEY FERGUSON 12 V
The 650-092 Printed Circuit Board for gensets OLYMPIAN-MASSEY FERGUSON 24 V
We offer a great stock and wide variety on OLYMPIAN and MASSEY FERGUSON Printed Circuit Boards.

 

1.650-091 PCB 12V
2.650-092 PCB 24V
3.917-422/630-464
4.917-423/630-465
5.917-530/630-466

Request
Callback

Product Details:

We Are Dealing Diesel Engine Operating With Saftys And Controls And We Ar Also Cummins, Cat, Kirloskar, Leyland, Bliss Spare Parts

Product Details:

WE ARE DEALING ALL TYPE OF DIESEL ENGINE CONTROLS AND OTHER OPERATION SPARE PARTS 

Product Details:

 3030256 Generator Electrical Speed Control Module

Description:
PCB board 3030256 for diesel Generator Other parts:

4914090 Normally Closed 350KW max

4914091 Normally Closed 800KW max

3044196 Normally Closed 350KW max

3062322 Normally Closed 800KW max

3098693 Normally Closed 800KW max

3037359 Normally Open 300KW max

3044195 Normally Closed 500KW max

3062323 Normally Closed 800KW max

3032733 Normally Closed 500KW max

3036453 Protect the diesel engine 
 

We also provide other models of speed controllers as follows:
 
Speed controller: ESC5500E, ESC5221, ESD5530, ESC5550E, 3044195, 3044196, 4914090, 4914091, 3062322
Actuator:ADC225, ADC175, ADC120, 3408324, 3408326, 3408328

Product Details:

The Be142 is 3-phase AMF controller. All parameters, alarms and operating functions are indicated by means of a high-luminosity display. The AMF controller Be142 interfaces with resistive or digital sensors. It measures Vac, Aac, Vdc, Hz, hour count, R.p.m., Oil Pressure, Engine Temperature, Battery Vdc and Fuel Level. Software for remote monitoring is also provided free of charge. The Be142 provides MODBUS via RS485. The AMF controller Be142 complies with NFPA-110 / NFPA-99. By using our TCP-IP server you can monitor and control the Be142 via INTERNET. Option for remote control by GSM is also provided. We provide support to make your own AMF Control Panels.  VIDEO PRESENTATION

[1] RS485 SERIAL INTERFACE  

[2] CONFIGURABLE DIGITA INPUTS CONNECTIONS  

[3] CONFIGURABLE ANALOGUE INPUTS CONNECTIONS  

[4] POWER SUPPLY AND BELT ALTERNATOR CONNECTIONS  

[5] CONFIGURABLE STATIC OUTPUT CONNECTIONS  

[6] 3-PHASE CURRENT TRANSFORMER CONNECTIONS  

[7] ALTERNATOR VOLTAGE CONNECTIONS

[8] REAR COVER FIXING SCREWS

[9] BE142 CONTROLLER FIXING SCREWS

[10] RESERVED AREA FOR END USER INFORMATION

The AMF Controller Be142 Front Fascia

[1] Manual ENGINE START Push Button    

[2] Manual ENGINE STOP Push Button  

[3] GENERATOR PARAMETERS status  indicator  

[4] To Close the GENERATOR circuit breaker  

[5] To Open a Circuit breaker   [6] To Close tha MAINS circuit breaker   

[7] MAINS status indication   [8] MANUAL MODE of operation  

[9] OFF MODE of operation   [10] AUTO MODE of operation 

[11] TEST MODE of operation   [12] ALARM SILENCE push button

[13] F9 DISPLAY navigation push button   

[14] 4-DIGIT display for Measurement & Menus 

[15] F8 DISPLAY navigation push button 

[16] ALARM identifiers 

[17] GENERATOR control panel

 

Product Details:

PCB Board 650-044 printed circuit board

630-088 EIM (PREVIOUSLY 630-465) Interface 630-465 for gensets 12 V

630-089 EIM (PREVIOUSLY 630-466) Interface 630-466 for gensets 24 V

1. PCB 650-091, 12V
2. PCB 650-092, 24V
3. EIM 630-465/ 917-423// 630-088, 12V
4. EIM 630-466/ 917-530/630-089, 24V
5. 650-044
6. 650-066

Product Details:

The 650-091 Printed and 650-092 Circuit Board for gensets OLYMPIAN-MASSEY FERGUSON 12 V.

We offer a great stock and wide variety on OLYMPIAN and MASSEY FERGUSON Printed Circuit Boards.

 

• 650-091 PCB 12V
• 650-092 PCB 24V
• 917-422/630-464
• 917-423/630-465
• 917-530/630-466

 

Product Details:

WE ARE DEALING  PT SPEED CONTROLLER AND PT ACTUATOR / SENSOR/ SWITCHES AND ALL PANELS ETC